Hyundai Kona: Controller / Heater & A/C Control Unit (DATC) Components and components location
| Components |
|
Pin NO |
Function |
Pin NO |
Function |
|
1 |
Battery (+) |
21 |
IGN2 |
|
2 |
ISG B+ |
22 |
IGN1 |
|
3 |
ILL+ (TAIL) |
23 |
Blower motor (+) |
|
4 |
Sensor REF (+5V) |
24 |
Photo sensor_LH |
|
5 |
Mode actuator feedback |
25 |
- |
|
6 |
Temperature actuator feedback |
26 |
- |
|
7 |
Intake actuator feedback |
27 |
- |
|
8 |
EVAP Sensor (+) |
28 |
PTC Relay 3 |
|
9 |
AMB Sensor (+) |
29 |
PTC Relay 2 |
|
10 |
Mode actuator (Vent) |
30 |
PTC on signal |
|
11 |
Mode actuator (Defrost) |
31 |
Detent OUT (-) |
|
12 |
Temperature actuator (Cool) |
32 |
- |
|
13 |
Temperature actuator (Warm) |
33 |
C_CAN High |
|
14 |
Intake actuator (Fresh Air) |
34 |
C_CAN Low |
|
15 |
Intake actuator (Recirculated Air) |
35 |
Power mosfet (Drain feed back) |
|
16 |
HTD (Rear defog indicator) |
36 |
Power mosfet (Gate) |
|
17 |
Rear defog switch |
37 |
ECV + |
|
18 |
Clean signal |
38 |
ECV- (Ground) |
|
19 |
Ionizer diagnosis |
39 |
Sensor ground |
|
20 |
ILL- (RHEO) |
40 |
Ground |
|
Pin NO |
Function |
Pin NO |
Function |
|
1 |
PAB IGN1 |
9 |
SBR 2 Row Middle |
|
2 |
PAB Cut Off signal |
10 |
SBR 2 Row Right |
|
3 |
PAB On signal |
11 |
- |
|
4 |
Auto defogging (Feedback) |
12 |
Auto defogging (TEMP) |
|
5 |
Auto defogging (Open) |
13 |
Auto defogging (SCK) |
|
6 |
Auto defogging (Off) |
14 |
Auto defogging (Data) |
|
7 |
SBR Passenser |
15 |
- |
|
8 |
SBR 2 Row Left |
16 |
Ground |
Heater & A/C Control Unit (Manual) Repair procedures
Replacement
1.
Disconnect the negative (-) battery terminal.
2.
Remove the crash pad lower panel.
(Refer to Cr ...
Heater & A/C Control Unit (DATC) Repair procedures
Self Diagnosis
1.
Self-diagnosis process.
...
Other information:
Hyundai Kona (OS) 2018-2024 Owners Manual: In case of an emergency while driving
If the engine stalls while driving
Reduce your speed gradually, keeping a straight line. Move cautiously
off the road to a safe place.
Turn on your hazard warning flasher.
Try to start the engine again. If your vehicle will not start, we recommend
that you contact an authorized HYUNDAI deale ...
Hyundai Kona (OS) 2018-2024 Service Manual: Rear Door Outside Handle Repair procedures
Replacement
1.
Remove the plug hole.
2.
After loosening the mounting bolt, remove the rear door outside handle
cover (A).
Tightening torque :
7.8 - 10.8 N.m (0.8 - 1.1 kgf.m, 5.8 - 8.0 lb-ft)
...
