Hyundai Kona: Lubrication System / Engine Oil Repair procedures

Hyundai Kona (OS) 2018-2026 Service Manual / Engine Mechanical System / Lubrication System / Engine Oil Repair procedures

Replacement

•	Prolonged and repeated contact with mineral oil will result in the removal of natural fats from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

•	Exercise caution in order to minimize the length and frequency of contact of your skin to used oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use water-less hand cleaner, to remove any used engine oil. Do not use gasoline, thinners, or solvents.

•	In order to preserve the environment, used oil and used oil filter must be disposed of only at designated disposal sites.

Drain the engine oil.

(1)	Remove the oil filler cap.

(2)	Remove the oil drain plug (A), and drain the oil into a container.

Remove the oil filter with the SST (09263-2E000, the oil filter wrench).

(1)	Remove the oil filter (A).

(2)	Check and clean the oil filter installation surface.

(3)	Check the part number of the new oil filter is as same as old one.

(4)	Apply clean engine oil to the gasket of a new oil filter.

(5)	Lightly screw the oil filter into place, and tighten it until the gasket contacts the seat.

(6)

Tighten it with the torque below.

Tightening torque :

11.8 - 15.7 N.m (1.2 - 1.6 kgf.m, 8.7 - 11.6 lb-ft)

Refill with engine oil.

(1)

Clean and install the oil drain plug with a new gasket.

Tightening torque :

34.3 - 44.1 N.m (3.5 - 4.5 kgf.m, 25.3 - 32.5 lb-ft)

(2)

Fill with fresh engine oil.

Capacity

Total : 4.6 - 4.9 L (1.21 - 1.29 U.S.gal., 4.86 - 5.17 U.S.qt., 4.04 - 4.30 lmp.qt.)

Oil pan : 4.2 L (1.10 U.S.gal., 4.43 U.S.qt., 1.10 lmp.qt.)

Drain and refill in cluding oil filter :

4.5 L (1.18 U.S.gal., 4.75 U.S.qt., 3.95 lmp.qt.)

(3)	Install the oil filler cap.

4.	Start engine and check for oil leaks.

5.	Recheck the engine oil level.

Inspection

Engine Oil

1.	Check the engine oil quality. Check the oil deterioration, entry of water, discoloring of thinning. If the quality is visibly poor, replace the oil.

Check the engine oil level.

After warning up the engine and then 5 minutes after the engine stop, oil level should be between the "L" and "F" marks in the dipstick.

If low, check for leakage and add oil up to the "F" mark.

•	Do not fill with engine oil above the "F" mark.

Selection of Engine Oil

Specifications : ACEA A5, 5W-30

•	If not available, API SL, ILSAC GF-3, ACEA A3 can be used.

Allowed SAE Viscosity

For best performance and maximum protection of all types of operation, select only those lubricants which :

1)	Satisfy the requirement of the ACEA classification.

2)	Have proper SAE grade number for expected ambient temperature range.

3)	Lubricants that do not have both an SAE grade number and ACEA service classification on the container should not be used.

Lubrication System

...

Oil Pressure Switch Repair procedures

Removal and Installation 1. Disconnect the battery negative terminal. 2. Remove the under cover. (Refer to Engine and Transaxle Ass ...

Other information:

Hyundai Kona (OS) 2018-2026 Service Manual: Knock Sensor (KS) Description and operation
Description Knocking is a phenomenon characterized by undesirable vibration and noise and can cause engine damage. Knock Sensor (KS) is installed on the cylinder block and senses engine knocking. When knocking occurs, the vibration from the cylinder block is applied as pres ...

Hyundai Kona (OS) 2018-2026 Owners Manual: Front seat headrests
The driver’s and front passenger’s seats are equipped with adjustable headrests for the passengers safety and comfort. Adjusting the height up and down To raise the headrest: 1. Pull it up to the desired position (1). To lower the headrest: 1. Push and hold the release button (2) on the headr ...