Hyundai Kona: Audio / Speakers Repair procedures

Hyundai Kona (OS) 2018-2023 Service Manual / Body Electrical System / Audio / Speakers Repair procedures

Inspection

Troubleshooting for Speaker

(1)	Basic inspection of speaker Inspect the sound from speaker after verifying that the speaker mounting screws is removed and the wiring connector is connected precisely to remove vibration transmitted from body trims and surrounding parts.

(2)

Case Troubleshooting

Case

Inspection/Remedy

Trembling sound

1)	Before replacing the speaker, inspect that the mounting screw is installed normally.

2)	After re-installing the speaker, verify that no trembling sound is heard.

3)	When hearing a trembling sound again, replace the speaker with new one.

Noise

1)	Check if the wiring connector is connected normally. If not, reconnect the wiring connector.

2)	In case of radio static, check if there is a noise from CD player.

3)	When a noise is heard on turning radio and CD on, replace the speaker with new one.

•	In case there is only radio static, this causes from poor radio reception. Thus the speaker needs no repair and replacement.

Poor working

Inspection of the wiring connection between the battery and the speaker

1)	Before replacing the speaker, inspect the wiring and connections in the speaker circuit.

2)	Check the supplying power to the speaker and the resistance, and then inspect the sound quality.

3)	If the speaker works poorly, replace it with new one.

•	During dealing of speaker

•	Dropping or rough handling of the speaker can cause damage.

•	Be careful not to cover water and oil over the speaker.

•	Caution during dealing of speaker because the material of diaphragm is paper which is easy to be torn by impact and external force.

•	When modifying audio system as customer pleases, this does electric damage to speaker.

•	And, in this case the speakers are not covered by the manufacturer's warranty.

Removal

[Front Door Speakers]

1.	Disconnect the negative (-) battery terminal.

2.	Remove the front door trim. (Refer to Body - "Front Door Trim")

3.	Remove the front door speaker (B) after disconnecting the connector (A) and loosening the screws.

[Front Door Tweeter Speaker]

1.	Disconnect the negative (-) battery terminal.

2.	Remove the front door trim. (Refer to Body - "Front Door Trim")

3.	Remove the tweeter speaker (A) after loosening the screws.

[Rear Door Speakers ]

1.	Disconnect the negative (-) battery terminal.

2.	Remove the rear door trim. (Refer to Body - "Rear Door Trim")

3.	Remove the rear door speaker (B) after disconnecting the connector (A) and loosening the screws.

Installation

Front Door Speaker

1.	Install the front door speaker.

2.	Install the front door trim.

3.	Connect the negative (-) battery terminal.

Front Door Tweeter Speakers

1.	Install the front door tweeter speaker.

2.	Install the front door trim.

3.	Connect the negative (-) battery terminal.

Rear Door Speaker

1.	Install the rear door speaker.

2.	Install the front door trim.

3.	Connect the negative (-) battery terminal.

•	Make sure the speaker connectors are plugged in properly.

Audio Unit Repair procedures

Removal 1. Disconnect the negative (-) battery terminal. 2. Remove the center fascia panal. (Refer to Body - "Center Fascia Pa ...

Antenna Repair procedures

Removal Roof Antenna 1. Disconnect the negative (-) battery terminal. 2. Remove the roof trim assembly. (Refer to Body - " ...

Other information:

Hyundai Kona (OS) 2018-2023 Owners Manual: Hazard warning flasher
The hazard warning flasher serves as a warning to other drivers to exercise extreme caution when approaching, overtaking, or passing your vehicle. It should be used whenever emergency repairs are being made or when the vehicle is stopped near the edge of a roadway. To turn the hazard warning flas ...

Hyundai Kona (OS) 2018-2023 Service Manual: Exhaust Gas Temperature Sensor (EGTS) Schematic diagrams
Circuit Diagram EGTS #1 Harness Connector EGTS #2 Harness Connector ...