Hyundai Kona: Repair procedures / Side Impact Sensor (SIS) Repair procedures

Hyundai Kona (OS) 2018-2023 Service Manual / Restraint / Repair procedures / Side Impact Sensor (SIS) Repair procedures

Removal

Pressure Side Impact Sensor

•	Removal of the airbag must be performed according to the precautions/procedures described previously.

•	Before disconnecting the side impact sensor connector(s), disconnect the side airbag connector(s).

•	Do not turn the ignition switch ON and do not connect the battery cable while replacing the side impact sensor.

1.	Disconnect the battery negative cable, and wait for at least three minutes before beginning work.

2.	Remove the front door trim. (Refer to Body - "Front Door Trim")

3.	Loosen the mounting bolt and then remove the sidet impact sensor after disconnecting the connector (A).

Gravity Side Impact Sensor

1.	Disconnect the battery negative cable and wait for at least three minutes before beginning work.

2.	Remove the door scuff trim. (Refer to Body - "Interior Trim")

3.	Remove the center pillar trim. (Refer to Body - "Interior Trim")

4.	Loosen the mounting bolt and then remove the sidet impact sensor after disconnecting the connector (A).

Installation

Pressure Side Impact Sensor

Install the pressure side impact sensor with the screw then connect the pressure side impact sensor connector.

Tightening torque :

2.0 - 2.9 N.m (0.2 - 0.3 kgf.m, 1.4 - 2.2 lb-ft)

2.	Install the front door trim. (Refer to Body - "Front Door Trim")

3.	Reconnect the battery negative cable.

After installing the pressure side impact sensor, confirm proper system operation:

•	Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.

•	You must comply with the specified tightening torques with the tool specified because Pressure – Side Impact Sensors (P-SIS) may be broken or POP-NUT may be rotated.

•	Problems may be occurred in the durability of P-SIS or impact sensing performance may be depreciated if POP-NUT is rotated.

•	The door module must not be transformed because SRSCM judges a impact through the pressure sensor in the door module.

Gravity Side Impact Sensor

•	Do not turn the ignition switch ON and do not connect the battery cable while replacing the side impact sensor.

Install the side impact sensor with the bolt then connect the side impact sensor connector.

Tightening torque :

7.8 - 9.8 N.m (0.8 - 1.0 kgf.m, 5.8 - 7.2 lb-ft)

2.	Install the center pillar trim. (Refer to Body - "Interior Trim")

3.	Install the door scuff trim. (Refer to Body - "Interior Trim")

4.	Reconnect the battery negative cable.

After installing the Side Impact Sensor, confirm proper system operation :

•	Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.

Side Impact Sensor (SIS) Description and operation

Description • Side Impact Sensors (SIS), each installed on the center part of the right and left front door modules and the right and left center pillars, ...

Seat Belt Buckle Switch (BS) Components and components location

Components 1. Seat Belt Buckle Switch (BS) ...

Other information:

Hyundai Kona (OS) 2018-2023 Owners Manual: Sliding the sunroof
Pressing the sunroof control lever backward or forward momentarily to the second detent position completely opens or closes the sunroof even when the switch is released. To stop the sunroof at the desired position while the sunroof is in operation, press the sunroof control lever backward or forw ...

Hyundai Kona (OS) 2018-2023 Service Manual: Schematic diagrams
Operation Condition for the ISG function Operation Condition for the ISG function After every engine start, the function is automatically active and on stand-by. The ISG OFF switch can be used to deactivate the function manually until the next terminal change. Pressing ...